A trick courtesy of Tony Boggus.
by Hoot 
, Diversityville, Liberal-sota, Monday, October 17, 2016, 11:43 (2961 days ago) @ Jared
Thread files will cut serrations pretty quickly. You just need to pick a pitch and slowly cut straight across the sight face keeping repeated cuts in the same grooves. Maybe practice on the edge of a piece of scrap would be useful.
This popped up on Amazon but I expect Brownells or any industrial tool supply will have them as well. https://www.amazon.com/Nicholson-Thread-Restoring-Square-Metric/dp/B000LEGYPK/ref=pd_si...
I only selected this as an example. In fact, I didn't even note the thread pitch so I couldn't say if it was too fine or too coarse.
Complete thread:
- 94 Trapper in 30-30 nice little gun lousy sights... Need -
Rob Leahy,
2016-10-12, 19:11
![[*]](themes/default/images/complete_thread.png "Open whole thread")
- My default choice would be the Williams FP, then a STEEL -
Hobie,
2016-10-12, 19:14
- I put a Williams receiver sight on mine too - stonewalrus, 2016-10-12, 21:04
- I put a Williams FP on mine and am happy with it - JD, 2016-10-13, 14:40
- Sort of agree with Hobie. - Jimmy P., 2016-10-12, 20:06
- Might try Skinner. - Wildcat, 2016-10-13, 09:27
- 94 Trapper in 30-30 nice little gun lousy sights... Need - Drago, 2016-10-13, 09:44
- Hey Rob, "lousy sights"? -
Drago,
2016-10-13, 11:56
- ;-) I am pretty sure the Duke had a brass bead, the Rifleman -
Rob Leahy,
2016-10-14, 08:28
- HEY ROB! McCAIN DID USE HIS SIGHTS... - Drago, 2016-10-14, 16:08
- ;-) I am pretty sure the Duke had a brass bead, the Rifleman -
Rob Leahy,
2016-10-14, 08:28
- 94 Trapper in 30-30 nice little gun lousy sights... Need -
Sarge,
2016-10-13, 20:32
- Thanks all! Good answers. I neglected to mention this wasn't -
Rob Leahy,
2016-10-14, 08:40
- Thanks all! Good answers. I neglected to mention this wasn't -
Jared,
2016-10-14, 09:33
- Remove the white line and blacken the sight for a good post. -
Hobie,
2016-10-14, 18:31
- Remove the white line and blacken the sight for a good post. -
Jared,
2016-10-14, 23:58
- Ok, so cutting the face of the sight might not be a cost -
Hobie,
2016-10-16, 21:53
- Ok, so cutting the face of the sight might not be a cost -
Jared,
2016-10-17, 08:26
- A trick courtesy of Tony Boggus. -
Hoot,
2016-10-17, 11:43
- A trick courtesy of Tony Boggus. -
Jared,
2016-10-17, 23:22
- A trick courtesy of Tony Boggus. -
Sarge,
2016-10-18, 16:04
- A trick courtesy of Tony Boggus. -
Jared,
2016-10-19, 08:18
- Gotcha... -
Sarge,
2016-10-19, 12:29
- Swiss Grobet #0 serrating file, 30 LPI works for me. -
John K.,
2016-10-19, 13:36
- Pic -
John K.,
2016-10-19, 14:31
- Thanks John - Sarge, 2016-10-19, 18:07
- Pic - Jared, 2016-10-19, 22:19
- Pic -
John K.,
2016-10-19, 14:31
- Swiss Grobet #0 serrating file, 30 LPI works for me. -
John K.,
2016-10-19, 13:36
- Gotcha... -
Sarge,
2016-10-19, 12:29
- A trick courtesy of Tony Boggus. -
Jared,
2016-10-19, 08:18
- A trick courtesy of Tony Boggus. -
Sarge,
2016-10-18, 16:04
- A trick courtesy of Tony Boggus. -
Jared,
2016-10-17, 23:22
- I've been making do with what I've got all my life, so it -
Hobie,
2016-10-18, 20:01
- I've been making do with what I've got all my life, so it - Jared, 2016-10-19, 08:20
- A trick courtesy of Tony Boggus. -
Hoot,
2016-10-17, 11:43
- Ok, so cutting the face of the sight might not be a cost -
Jared,
2016-10-17, 08:26
- Ok, so cutting the face of the sight might not be a cost -
Hobie,
2016-10-16, 21:53
- Remove the white line and blacken the sight for a good post. -
Jared,
2016-10-14, 23:58
- Remove the white line and blacken the sight for a good post. -
Hobie,
2016-10-14, 18:31
- Rob, I have a Skinner on my .45 Colt '94 AE. - Hoot, 2016-10-14, 09:50
- Thanks all! Good answers. I neglected to mention this wasn't -
Jared,
2016-10-14, 09:33
- Thanks all! Good answers. I neglected to mention this wasn't -
Rob Leahy,
2016-10-14, 08:40
- 94 Trapper in 30-30 nice little gun lousy sights... Need - Creeker, 2016-10-15, 09:32
- Check whether XS is still making their "cowboy" sights - B C, 2016-10-15, 16:05
- My default choice would be the Williams FP, then a STEEL -
Hobie,
2016-10-12, 19:14