I have hell.....
629-4 Mountain Gun. Went back to Smith for a hammer nose about a year ago, going for it's 2nd tomorrow. Maybe 1000 rounds on the hammer nose and very minimal dry firing. What is up?
![[image]](http://s673.photobucket.com/user/brycoarms/media/Mobile%20Uploads/CAM00529_zps14a7d022.jpg.html)
Is it centered.....
nose in the hammer?
hammer in the frame?
hole in the frame?
nose in the hole in the frame?
Seconded, Mark.
by Sarge 
, Central Misery, Wednesday, May 14, 2014, 17:03 (3852 days ago) @ MR
I've seen a boatload of old Smiffs used hard over the past 35 years and I never saw one consistently do that. I suspect bad frame machining, though trying a new hammer would be another approach.
I have seen one other. On this forum, actually, years ago
another mountain gun breaking firing pins. Belonged to ***. Or maybe it was when he went by *****. Or ******.
Anyway, it made several trips back and I cannot remember if it ever quit breaking pins.
In his case, he & S&W said everything lined up. Always wondered if perhaps the cylinder had enough free rotational slop to shear off the pin nose at the moment of firing.
I have seen one other. On this forum, actually, years ago
by Slow Hand , Indiana, Wednesday, May 14, 2014, 19:20 (3852 days ago) @ John K.
If you are talking about who I think you are; I'm sure his moutain gun was the best gun ever devised...until the next week when he found something new and that thing was an unreliable, hunk of junk!
I have safe full of Rugers Scott....
and 3 Smiths.....this is one of the reasons............
Bud, I have a Safe full of Smiths & Have NEVER had one do
by Rob Leahy , Prescott, Arizona, Thursday, May 15, 2014, 16:26 (3851 days ago) @ Bud
that.
--
Of the Troops & For the Troops
Same here Bud...
by rob , Friday, May 16, 2014, 21:13 (3850 days ago) @ Bud
I have a safe full of Rugers and only one S&W at this point (a 629-4 4"). While I dearly love the 629, and would joyously celebrate the arrival of a 686 or 627, I do tend to baby it. I'll shoot just about any sane load in my GP100 or SBH and dry fire them with reckless abandon. They are just tanks.
Buy another hammer on Ebay.
Might solve the problem, and if nothing else it will be cheaper and easier than getting the pin replaced. (Assuming S&W isn't picking up the tab and the shipping)
Buy another hammer on Ebay.
S&W is picking up shipping both ways along with the repair. Thankfully, the gun is covered under Lifetime Service. Interesting note, Smith no longer supports the forged hammers and triggers. A call asking to buy a new hammer nose to install will be answered with a "no". They will not install a new hammer nose if one just sends back the hammer, covered under warranty or not. They insist on the entire gun. Unless they perform a miracle and really make a believer out of me, I imagine this 629-4 will become trade fodder.
CAS...
I have several N frame hammers who's hammer nose's are now like gold. I can keep putting new hammers, but if the gun keeps breaking the hammer noses it makes for a expensive temporary repair.
This is one reason I don't get worked up...
by rob , Friday, May 16, 2014, 21:21 (3850 days ago) @ Scott Ambler
Over frame mounted firing pins. I flat out do not ever dry fire my 629-4 or my 1917 Colt (though I used to dry fire the crap out of it when I was just a kid...I'm amazed I didn't wear it out in the house!) and it is not advised to do so. It is a very very very rare frame mounted firing pin that brakes.
Scott, don't know if this helps but...
by Hoot , Diversityville, Liberal-sota, Monday, May 19, 2014, 06:31 (3848 days ago) @ Scott Ambler
Power Custom sells S&W hammer noses. I see them on Midway's site here => http://www.midwayusa.com/product/964902/power-custom-smith-and-wesson-hammer-nose-rivet...
I can't say if they offer anything over the factory part but at least they are available to the common man.